Stay Current
Boats Priced to Move!
Sent to You Weekly!
Insert Your
E-mail Address

Presented by:
Fort Lauderdale, Florida
Photo 1 of 13
Not for sale to U.S. Residents while in U.S. waters.

Northrop and Johnson
(954) 522-3344

 Not for sale to U.S. Residents while in U.S. waters.

Jack 206 495 2912


Three cabin layout, plus crew quarters forward, all with ensuite baths. Extraordinary value! MALINCHE was commissioned in 2005 for a family cruise from the Mediterranean to the Caribbean, where she is now offered for sale and ready for her next adventure.


The quality of the interior woodwork and craftsmanship is outstanding, featuring high-grade teak with a rich multi-coat gloss finish. Saloon seating is white leather and the headliner is done in Alcantara fabric. Halogen lighting with stabilized power in each cabin.

Specifications, with Equipment and Information:
- Length: 67' 0"
- Max Height: 0
- LOA: 66.6666' 0"
- LWL: 56.5' 0"
- BEAM: 17.5' 0"
- DRAFT: 8.5833' 0"
- Engine(s): 4LHA-STP
- Fuel: 369.841 Gal
- Water: 528.344 Gal
- Holding: 116.236 Gal
- Hull Construction: Fiberglass Sandwich
- Manufacturer: NORTH WIND
- Model: Deck Saloon


A very spacious and inviting salon is located amidships and features a U-shaped dinette to port with matching settee and chart table forward opposite. The engine and generator access is via a large centerline hinged floorboard. The deck saloon design allows room for the machinery to be located below the salon and on the center axis of the boat, thus keeping the center of gravity low and greatly enhancing the performance characteristics of the boat. A full panoramic view is enjoyed through the curved grey tinted wrap-around reinforced windows.

The entertainment center is incorporated into the cabinetry above the settee on the starboard side with the focal point being a 26" Flat screen TV.  

Master Stateroom

The full beam master suite is accessed via a corridor on the port side. A centerline queen berth is symmetrically balanced on each side with cushioned seating, storage and built in vanities. Generous size hanging lockers outboard and a Flat screen TV mounted on the center bulkhead. The master bath is outboard and includes a separate full size shower, Corian counter, vanity, electric toilet, and cabinets.


The U-shaped galley is located aft and down two steps on the starboard side and offers every modern convenience imaginable, including stainless steel appliances, dishwasher and microwave.


Galley equipment:
Stainless steel appliances
Force 10 stove with three burners, oven and SS safety bar.
Bosch refrigerator/freezer
Bosch dishwasher
Bosch washer/dryer
Bosch microwave
Bosch air extractor
Scotsman icemaker

Guest Staterooms

Forward and two steps down from the salon there is a centerline bulkhead that separates the two guest cabins. The port guest cabin has three single berths; (an over/under configuration outboard and a single opposite), with hanging and draw storage. The head is forward and also serves as access to the skippers cabin. The starboard guest cabin features a double berth with a single above and head forward. Guest baths feature vanities with Corian counters, stall shower, and electric toilets.

Crew Accommodations

The skippers cabin has twin berths, (over/under) and a private bath with vanity and manual toilet.

Electronics and Navi

Raymarine package;
Chartplotter - 2 displays
Satellite communications - Nera - Fleet 33
Weather fax
20" TV - Sharp LCD
26" TV - Sharp LCD
Sharp DVD player
Pioneer stereo system w/Bose speakers
Computer, monitor & printer


24 volt DC - 230 volt AC
Generator - Northern Lights 10 kW in soundproof housing.
Set of 8 x 24V 920 Amp/h gel service batteries.
2 engine starter and generator batteries of 120 Amp/12V.
Alternator amp charge indicator.
One parallel switch for generator starting batteries.
1 x 110 Amp / 24 V service alternator
1 x 80 Amp / 24 V alternator
Mastervolt 12V battery charger
Mastervolt 24V/100Amp service battery charger
Mastervolt inverter 24V/220V
Independent 12V / 24V and 220V distribution boxes.
28V Halogen lighting lamps with stabilized power in each cabin.

Deck and Hull

All deck gear made from Stainless Steel AISI 316 or 316L with a "mirror polish" on their visible surfaces.
Solid Burma teak around the gunwales from bow to stern, with 6 cleats and fairleads exclusively designed by Northwind Yachts. The openings on the gunwales allow an effective water evacuation keeping the deck dryer and cleaner.

The entire deck, except the coach roof, is finished off with glued thick Burma Teak strips that are caulked and primed with rubber strips to guarantee water tightness.

The rest of the deck is finished off with two different kinds of non-slip surfaces, depending on the area.
White isophtalic polished gel coat is used to finish off the vertical cabin sides and coamings. The coaming is finished with varnished solid teak strip.

Two solid varnished Burma Teak handrails designed by Northwind are fitted on the external sides of the cabin to allow safe movements along on the deck towards the bow.

Saloon entrance hatch is provided with a locker with a sliding cover on its upper side, and another locker on its vertical side with a sliding cover fitted with a hydraulic locking system that keeps both sides sunken into the hull.

Foldaway spray hood and sunshade with Stainless Steel AISI 316 fittings. Spray hood and sunshade are kept sunken into the deck.

The mast halyards reach the cockpit and are sunken into the double saloon ceiling allowing the deck to be kept clear.

The cockpit lockers allow the stowage of the mooring ropes. Winch covers and cockpit table cover.

Deck Equipment

(2) Hatches and 2 portholes in the aft head,
(2) Additional hatches and two portholes in the aft cabin.
Sail locker deck hatch
Deck saloon with panoramic 10 mm reinforced grey tinted glass windows recessed in a fiberglass frame and glued with special UV resistant adhesives
2nd aft Skippers cockpit with leather covered steering wheel and compass.
Stainless steel emergency tiller controlled from the deck, works the rudder shaft directly.
Guest cockpit with Burma Teak foldable table and bottle storage lockers with refrigerator.
Guest cockpit cushions
 Hydraulic anchoring windlass with cockpit control
Delta 48 kg anchor, with 100 metres of 12 mm Ø galvanized and calibrated chain.

(2) 50m 25mm Ø mooring spring lines.
Six 320 mm cylindrical and two 520mm spherical fenders.
Stanchion base, flag pole and flag. 

Northwind designed stainless steel rigging chain plates, solidly screwed and sealed to its counter plate and joined to a solid stainless steel structure, welded and laminated to the hull. This design allows the transmission of the generated efforts of the rigging directly to the hull.
Bow stainless steel reinforcement with a "mirror polish finish" on all its external sides with added stay fittings.
Stainless steel reinforcement counter plates laminated and bolted under its tip.
The bow top includes two bronze sheaves for the anchor and another in Teflon.
All the anchor gear is concealed in a locker keeping the bow clean and free of clutter.
(8) mooring cleats in stainless steel polished with mirror finish with counter plates laminated into the hull according to Northwind design and specifications.
(5) fixed eyebolts with counter plate for the retention of the boom and jacklines on the deck.
(2) foldaway eyebolts in the cockpit for the safety harnesses.
Stainless steel flat bottomed stanchion bases, with solid buttress to insert stanchions. These are made from stainless steel tubes, with adjustable cable lifelines tubes and tensioners with a height of 70 cm
Two gates on each side near the boarding ladder and another on the deck and an access gate at the stern for the gangway.
Teak and aluminium gangway with stanchion and cables at the stern.
(2) Backstays with hydraulic tensioners
(2) davits in the stern
Stern rail seats
(2) hatches in the raised saloon cabin
(3) hatches in the coach roof, one for each bow cabin.
(3) small portholes in the coach roof.
(2) hatches in the aft cabin.

Mast and Rigging

Hall Spars Carbon Mast Leisure Furl boom - hydraulically controlled
Reckmann hydraulic Genoa furling.
Reckmann hydraulic Stay-sail furling.
Rod rigging.
Running rigging with pre-tightened textile halyards: 1 main halyard, 1 spinnaker halyard,
Genoa halyard, 1 emergency halyard, and 1 top lift
(2) Navtec hydraulic backstay tensioners
Navtec hydraulic boomvang.
Deck floodlight and lights in the first spreader section.
(2) Cockpit lights on the boom.
Mast head navigation and anchor light.


Quantum in-boom furling main sail
Quantum genoa - 130%
Quantum stay-sail
Asymmetrical spinnaker

Winches and Deck Har

Two primary Lewmar 77 CST two speed, self-tailing, hydraulically operated winches for Genoa.
Two secondary Lewmar 64 CST two speed, self-tailing, hydraulically operated winches.
Two 64 CST Lewmar two speed, self-tail, hydraulically operated winches for spinnaker.
Two 64 series Lewmar self-tailing winches, one hydraulic, one manual at mast base.
Complete Genoa sail tracks and blocks.
Complete Main Sail traveller with blocks and stoppers.
Cabin top line handlers/clutches.
Complete Stay-sail self-tacking traveller with blocks, lines led back to cockpit.
Complete running rigging.


Hull and deck are hand laminated in a temperature and humidity controlled environment.
Hull molded by infusion technique with Vinylester Resin that protects dry and wet sides against osmotic process. Manually compacted lamination process with a metallic roller. The PVC core is welded to the lamination with special adhesives through vacuum molding system.

Multiaxial glass fibre material, laminated with special reinforcements to protect against collisions.
The Hull is finished in its external side with a white isophthalic gel coat, and the wet side is protected with additional layers of a high solid content epoxidic paint, which works as an extra barrier against osmosis.

The inner side of the hull is protected with special two-part polyester paints. The internal reinforcements are manufactured from PVC foam and are laminated.

The sandwich deck is also hand molded with vinyl ester resin using metallic rollers. The core is welded with special adhesives.

Stainless steel plates with solid lamination parts are used to reinforce the deck equipment. To guarantee water tightness, all the screwed parts on the deck are sealed with high resistance marine sealants.

Unidirectional fibers and plates are used to reinforce the deck-mounted gear. Hull and deck are perfectly joined and secured with stainless steel bolts every 15 cm and an inner lamination to guarantee water tightness and extraordinary strength.  All of the structural bulkheads are laminated to the hull and to the deck on both sides obtaining the extremely strong hull characteristic of a Northwind Yacht. The engine mounting is manufactured with polyester resin reinforced with a fiberglass lamination over a high density PVC foam core. Stainless steel plates are laminated where the elastic supports of the engine are placed and embedded into the laminate.


Cast lead bulb in the keel with 4% antimony to improve the mechanical characteristics. The sections follow a NACA profile. Keel and hull are solidly fitted together with stainless steel (AISI 316) bolts, sealed with marine adhesive with perimeter lamination. The rudder axis and its structure are made from aluminum. The rudder blade is made from fiber and resin with high-density foam, being saber shaped and is fitted to the hull with self aligning bearings. The top of the rudder stock has the connection for the emergency tiller, controlled from the deck.

Mechanical Equipment

Upgraded Yanmar 240 hp 4-cylinder diesel engine (4LHA-STP)
Rexroth central hydraulic system - Commander 400 - 24 volt
Bowthruster - Lewmar 8 KW - 24 volt
Air conditioning - Climma (multi-zone) chilled water system.
Passarelle - Besenzoni - Hydraulic stow-away w/remote control.
Air compressor - Bauer - Junior II
Simpson davits (electric).
110 Amp /24 V alternator
Engine control panel with tachometer, temperature, oil pressure, hours, alarms and start-stop gauges.
Morse throttle command at helm station.
Lewmar Rod steering - twin helms.
(3) Blade folding Gori propeller.
Flexible coupling from engine shaft to absorb vibrations.
Engine room blower.
Soundproof engine room with high density fire resistant rubber foam.
Automatic fire extinguishing system
Engine room lighting.
(2) 1400 litre aluminum diesel fuel tanks with inner baffles

Level indicator gauge, inspection and cleaning hatch in each fuel tank
Independent fuel fill pipes placed on each side of the boat.
(2) 1,000 liter capacity fresh water tanks.
Watermaker - Sea Recovery - Aqua Whisper 800 - 180 litre/hour.
Deck washing water pump.
60 litres hot water heater
Fresh and salt water foot pumps at galley.
(3) Electric toilets - 1 manual toilet (Crew cabin).
(4) 220 litre holding tanks.
Grey water system for all sinks/showers.

Tender and Safety Eq

Inflatable tender w/Honda 8 hp outboard
(2) Avon life rafts - Solas "A"
(7) lifejackets - Solas
Life ring
MOB - rescue pack
Emergency locator - McMurdo Nav6 plus


MALINCHE was ordered from Northwind by her one and only owner to be a safe and enjoyable platform for family fun. She has carried out this task admirably, and has been maintained with pride. She is immediately available to her next owner.


The name MALINCHE is reserved. Owner’s personal effects.  All items not specifically shown on this listing sheet.

Check out other listings from Northrop and Johnson!
OYSTER MARINE LTD SailBoat For Sale-1989 OYSTER MARINE LTD-Fort Lauderdale, FL
NAUTOR'S SWAN SailBoat For Sale-2008 NAUTOR'S SWAN-Fort Lauderdale, FL
Please call or email us with any questions.
17 Rose Drive
Fort Lauderdale, FL 33316
Telephone: (954) 522-3344
Fax: 954.522.9500

Back to Top

Details of this vessel are offered in good faith by the Company. The Information cannot be guaranteed; therefore it is up to the Buyer, his Agents, or his Surveyors to verify.

Make an Offer Anytime!!
Just click "Email Us" from the Listing Above
~ Make an Offer ~ Get A Great Deal ~
Check out all the Used Yachts for Sale, Used Powerboats for Sale or Used Boats for Sale in the Special Sections...
Remember to Email Your Offer!!